CURING & PROCESSING

• All Stainless Steel construction.
• Fully programmable for processing heat cure acrylics.
• Process up to 9 flasks, using the Mestra Stainless Steel Clamps.
• Can be set for delayed start if required.
• If power failure occurs, unit will store program and when power is restored, will continue from where the interruption occurred and finish the cycle.
• 1750 watts.
• Dimensions: H 270mm x W 480mm x D 480mm.

Mestra E2 Washing and Polymerizing Machine

Two easy to set, programmable cycles; one for boil-out and shower using 6 high pressure water jets, the other for processing up to 12 flasks in one cycle.

• Made entirely of stainless steel.
• Overall measurements: H 450mm, W 635mm, D 405mm.
• Internal measurements: H 350mm, W 400mm, D 320mm.

• Large, solid boil out and processing unit for up to 12 flasks.
• High grade steel housing.
• Continuously adjustable temperature from 30-95 degrees Celcius.
• Individual spraying time adjustment with 6 minute timer, 24 hour timer, hand spray gun.
• Measurements: H 940mm, W 660mm, D 635mm.

• Automatic Polymerizing Unit.
• Stainless Steel pot with large 6 litre capacity.
• Fully programmable to control temperature, time and pressure.
• Easy to drain and refresh water.
• Will reach and hold 100 degrees Celsius at 2 bar.
• Internal Dimensions: H 145mm x 220 diameter.
• Overall Dimensions: H 350mm x W 360mm x D 400mm.

• Pressure polymerisation unit with a temperature range up to 95 degrees C.
• Variable pressure from 3 to 6 bar.
• Thanks to its large capacity, the pressure pot can polymerise a large quantity of work.
• Easily holds 4 clear megacast flasks.
• Dimensions: H 310 x W 345 x D 385mm.
• Internal Dimensions of pot: Diameter 220 x Deep 174 mm.
• https://youtu.be/7dVLE4D7rwY

• Designed for self-cure acrylics.
• Can also hold temperature at maximum 135 degrees Celcius for the occasional heat cured job.
• Made from stainless steel and anodised aluminium.
• Triple safety system for safe lid opening.
• Time and temperature programmable.
• 1000 watts.
• Maximum pressure 6.5 bar
• H 320mm x W 310mm x D 395mm.
• Pot dimensions: 135mm diameter x 115mm deep.
• 20 kg

Stainless Steel Pressure Pot:

• 6 Litre
• Maximum Temperature Degrees.
• For cold & hot polymerizing at pressure up to 2kg /cm.
• Air hose.
• Double safety valve.
• Dimensions: H235 X W245 X L420 mm

Thermostatically controlled hotplate:

• Durable powder coated finish
• Pre-Set Temperature
• Up to 100°C
• Made in Germany
• 244 x 275 x 70mm

• Solid, portable, lightweight.
• Ideal for all self cure acrylics.
• 128mm inner diameter, 80mm deep.
• Will fit Lang Reline Jig, Denture Duplicator.

Please watch the instructional videos:

https://www.youtube.com/watch?v=KG5iLQ1ddss

https://www.youtube.com/watch?v=wurvgz_uG-s

Mestra Pressure Pot for self polymerizing resins

Mestra Pressure Pot allows repair and addition operations by using self polymerizing resins in order to improve work quality. Removes porosity and reduces colour changes in treated prosthesis.

• Dimensions Exterior: H 165mm, D 123mm
• Dimensions Interior: H 115mm, D 103mm

Mestra Clamp for Pressure Pot

Made of hardened duralumin in white colour.

Dimensions: W 130mm, H 175mm

Pressure pot is sold separately.

Essential for the elimination of micropores produced in casting rings linings by bubbles not eliminated, even by vacuum mixers. Thanks to the strong pressure (6-8 atmospheres) exerted on the lining, air bubbles are eliminated and the lining is compacted. This favours casting, particularly of hard metals such as Cr-Ni. 

External Dimensions: H 160 x D 150mm. 

Internal Dimensions: H 90 x D 110mm. 

Weight: 2 kg